Introduction of CFP packaging module

Jan 14, 2021

Leave a message

The DWDM optical communication module based on standardization has also won the high interest of the optical communication industry and wide acceptance of the market. Therefore, the development of 100G technology is inevitable. To achieve 100G rate, one solution is to use 10 channels to transmit 10Gbit / s each. CFP 100G module is to use this principle to achieve the upgrade from 10G to 100G. The 100G client module is a CFP module, which can support hot swap.


What are the CFP modules?

CFP MSA is the first industry standard to support 40 and 100Gbe Ethernet optical terminals. CFP multi-source protocol is to define a packaging specification of hot swap optical module to promote 40 and 100Gbit / s applications, including the next generation of high-speed Ethernet Applications (40 and 100Gbe). 100G CFP series optical modules are packaged in CFP, CFP2, CFP4 and CFP8. The size of CFP optical module is the largest, CFP2 optical module is half of CFP, and CFP4 optical module is a quarter of CFP. These optical modules cannot be used interchangeably, but they can be used in the same system at the same time.

 

CFP module

CFP, the abbreviation of C-form factor pluggable, is a kind of optical device which can transmit high-speed data signals, and it can usually transmit ultra-high rates of 40G, 100G or even 400G. CFP MSA defines the hardware interface specification and management interface specification of different rate CFP optical modules. CFP is a module that can support hot swap. It can support single 100G signal, OTU4, one or more 40G signals, OTU3 or STM-256 / oc-768.

CFP2 module

The volume of CFP2 module is only half of that of CFP module. It can support 10 10G channels, 4 *25G channels, 8*25G channels and 8*50G channels. 100G CFP2 is commonly used as 100G Ethernet interconnection link, which has higher transmission efficiency than CFP optical module, and smaller volume makes it suitable for higher density wiring. 

CFP4 module

The volume of CFP4 optical module is one fourth of that of CFP, with single mode and multi-mode options. CFP4 module can support four 10G channel transmission, and can be used for 40G / 100G Ethernet transmission, remote communication, etc.


CFP4 optical module has irreplaceable advantages

1. Higher transmission efficiency: the early 100G CFP optical module achieves 100G transmission rate through 10*10G channels, while the current 100G CFP4 optical module achieves 100G transmission through 4 25G channels, so the transmission efficiency is higher and the stability is stronger.

2. Smaller volume: the volume of CFP4 optical module is one fourth of that of CFP, which is the smallest optical module in CFP series.

3. Higher module integration: CFP2 is twice as integrated as CFP, and CFP4 is four times as integrated as CFP.

4. Lower power consumption and cost: the transmission efficiency of CFP4 optical module is significantly improved, but the power consumption is reduced, and the system cost is lower than that of CFP2.

CFP8 module

CFP8 module was proposed in 2015. CFP8 is an extension of CFP4. The number of channels is increased to 8, and the size is also increased accordingly. It is similar to CFP2, 40mm x 102mm x 9.5mm. Compared with the existing 100G transmission scheme, CFP8 module can provide more than four times the bandwidth, usually using 16 parallel 25G signals or 8 parallel 50G signals. Compared with using 8*50G for transmission, the cost of using 16*25G parallel signals is higher, and 16*25G lasers are needed. CFP8 module has compact structure and low power consumption. Generally speaking, it is a solution with high port density and high bandwidth.


Common application scenarios of CFP module

The 100G coherent optical module is mainly used for line side optical transmission in 100G wavelength division system. Compared with other kinds of line side optical modules, it has good OSNR performance, sensitivity, dispersion tolerance and DGD tolerance. DWDM technology with coherent CFP module is widely used in 100G man to meet its high capacity and long distance requirements.

100G multichannel DWDM transmission network

Because 100G rate is more easily affected by dispersion, it is necessary to compensate dispersion and increase optical power. First, a 100 GHz DWDM fiber multiplexer is used to combine all 100G rates, and then the dispersion compensation and amplification of the whole combination are carried out. This architecture can support the "buy on demand" of service providers. When the bandwidth is exhausted, the existing old 10G channel can be seamlessly exchanged with 100G service. The rest of the same components can even be reused to extend the data rate to 2.4 TB / s.

100G multichannel DWDM transmission network

The interface of CFP optical module is designed according to the optical module of SFP, but it provides 10 channels of 10Gbit / s or 4 channels of 25Gbit / s parallel data channels in the direction of receiving and transmitting, with a transmission rate of up to 100Gbps. Because of its continuous development, there are CFP2, CFP4, CFP8 and other classifications. 100G coherent CFP module can ensure the transmission performance and reduce the optical transmission loss, which is an effective solution for 100G man.


HTF's optical module products quality is guaranteed, and the accessories are imported.

Contact: support@htfuture.com

Skype :sales5_ 1909,WeChat :16635025029


Send Inquiry